Although motorcycle accidents can be caused by other factors, the most common causes are the same. Unsafe work zones and poorly placed grates and steel plates are all potential causes of motorcycle wrecks. Despite not being aware of all potential dangers, you can take steps to avoiding them. This article will discuss the most common causes of motorcycle accidents in construction. You can also learn about the steps to take if you are involved in one.

Distracted or inattentive driving

Several studies have shown that distracted or inattentive driving is a major cause of motorcycle accidents. In addition to being more difficult to notice than automobiles, motorcycles lack a number of safety features. This makes them particularly vulnerable to crashes. Motorcycle riders are also more likely to be thrown from their bikes and sustained severe injuries. So, how can distracted or inattentive driving be avoided?

In 2010, the U.S. Department of Transportation (DOT) held two national summits to address distracted driving and the motorcycle industry. U.S. DOT Secretary Ray LaHood testified at one of these hearings, and U.S. Senator Chuck Schumer was a witness at the other. Many drivers continue to engage in distracted driving behaviors. However, the latest legislation focuses on texting while driving and using hand-held electronic devices but ignores the main problem.

While working in a construction site, the driver may be looking at a construction sign, tuning the radio, or even texting. Distracted driving can cause serious accidents because distracted drivers can’t react in time. Distracted drivers are prone to fatal crashes, so they should be stopped if they cause one. This is an important part of the construction industry, so it’s vital to focus on safety when working in this field.

Screws and loose nails

A blowout on a motorcycle’s tire is one example of an accident that could be caused by loose nails or screws. These accidents are common in roadside construction. The sharp ends of the screw or nail can be ejected from the tire when the tire is flipped. A blowout can also be caused by the motorcycle’s movement. As a result, a rider may sustain injuries.

Speeding in a construction zone

Drivers who violate Indiana’s speed limits while driving in a construction zone can face enhanced penalties. In addition to putting lives at risk, speeding in a construction zone is illegal. A driver caught speeding through a construction zone will be cited with an additional fine of up to $1,000. The following tips can help prevent a motorcycle accident caused by speeding. These tips should not be ignored by drivers.

Speeding in construction zones can increase your chances of hitting another vehicle. Construction sites can also contain gravel, debris, or pits, which can cause rear-end collisions. Construction zones, unlike other types of roads, are often clogged with traffic so that drivers may not be able to see the motorcycles.

Motorcycle riders are especially at risk when speeding in construction zones. Motorcyclists must slow down to avoid hitting workers. Even the smallest inaccuracy can result in a horrific injury or even death. Motorcyclists who are injured may not be able to recover damages from negligent drivers. It is important to observe construction zone signs. After all, you don’t want to be caught driving in an unlit construction zone.

General contractor and site owner are liable

When a motorcycle accident occurs while working on a construction site, the party responsible for maintaining the conditions that led to the injury may be the general contractor or the site owner. Injuries caused by unsafe conditions or mistakes on the part of a supervisor may also be the fault of the general contractor or site owner. Depending on the state law, a general contractor or site owner can be held liable for injuries.

Typically, a construction site owner or contractor may be liable for a motorcycle accident if they were negligent or their workers were intoxicated or otherwise intoxicated. A general contractor is responsible for ensuring that all workers and site visitors are safe, including motorcycles. The general contractor must ensure safety regulations are followed and that competent employees are hired. Additionally, a subcontractor may be named in the lawsuit if they fail to perform these duties, or if they fail to warn their workers of dangerous conditions.

It is important to notify your employer immediately if the accident happened on a construction site. In addition, it is important to obtain the contact information of witnesses. Personal injury cases often require eyewitness accounts. Construction workers often have high turnover rates, which means it can be difficult to track down witnesses later. Taking the necessary steps to notify the employer and site owner of the motorcycle accident will greatly increase the chances of success.

How to handle a motorcycle accident

There are steps you can take right away if you are in an accident with a motorcycle on the job. The adrenaline that you feel after the accident may mask the severity of your injuries. If you have been hurt, wait for the paramedics to remove their protective gear before removing your own. Call 911 if you are seriously injured or have any other questions. Document your injuries and medical history after the accident and gather any medical records related to the incident.

Next, you should seek medical attention for your injuries and yourself. Call 911 if you have sustained any injuries, and get to a hospital as quickly as possible. Your condition may be severe, and the injuries you sustain may take days or even weeks to manifest. You may also suffer from serious internal bleeding or damage. You have a better chance of obtaining a settlement.

All medical records, including prescription and bills, should be kept. These records will serve as proof that you were injured and that you have an appropriate treatment plan. You may be eligible to receive compensation if you are unable to work or walk after the accident. You may also be entitled to a settlement from the responsible party. This can help you get the compensation you deserve for your injuries.

Compensation for a third-party claim

A third party claim is made when an entity other than the employer is partially at fault for your injury. While most construction accidents fall under the umbrella of workers’ compensation, sometimes you can file a third party claim to recover additional compensation for your injuries. Whether you’re looking to collect compensation from a third party, you must be aware of the process and the documents that you need to gather. You should consult a Palm Desert Motorcycle Accident Attorney if you have been hurt on the job.

A third-party claim is filed for the benefit of an injured worker, unlike other types of claims. In most cases, the liable party must prove that they were negligent or that your injuries were intentionally caused. In some cases, the ladder manufacturer may be sued for your injuries. These cases will require you to prove that the manufacturer was negligent by failing to attach to ladder rings or improperly marketing a defective product.

Document the details of an accident as soon after it occurs. Take pictures of the area and take names of witnesses. This can be invaluable in your claim. Remember that your story may change, and memories may be distorted with time. Gathering information from witnesses is crucial to your case. You could lose your right to compensation if you don’t.